EFFECTS OF CUTTING PARAMETERS ON CUTTING FORCE AND CHIP SHRINKAGE COEFFICIENTS IN HIGH-SPEED MILLING OF ALUMINUM ALLOY A7075

Pham Thi Hoa; Tran Viet Hoi; Phan Ngoc Tuan; Phan Dang Thuc

Pham Thi Hoa Faculty of Mechanical Engineering, Hung Yen University of Technology and Education
Tran Viet Hoi Hanoi University of Industry
Phan Ngoc Tuan Faculty of Mechanical Engineering, Hung Yen University of Technology and Education
Phan Dang Thuc Hanoi University of Industry

Abstract

This paper uses John-Cook material model to simulate by finite element method the high-speed milling of aluminum alloy A7075. Then the effects of cutting parameters, including cutting speed, depth of cut, and tool’s clearance angle on the cutting force and chip shrinkage coefficient, are analyzed. Applying Taguchi and ANOVA methods, the study also found the optimal cutting parameters for F and K of high-speed milling corresponding: V = 1,695 (m/min), t = 1.0 (mm), α = 15º and V = 1,695 (m/min), t = 1.5 (mm), α = 15º. The result of K and F after simulation with obtained parameter set is 1.43 and 51.63 (N), when using Taguchi Gray method to minimize F and K and the common set of parameters are V = 1,695 m/min, t = 1 mm, α = 15º.

References

X. Cui, B. Zhao, F. Jiao, and J. Zheng, “Chip formation and its effects on cutting force, tool temperature, tool stress, and cutting edge wear in high- and ultra-high-speed milling”. Int. J. Adv. Manuf. Technol., 2016, vol. 83, no. 1–4, pp. 55–65, doi: 10.1007/s00170-015-7539-7.

G. Bolar and S. N. Joshi, “3D finite element modeling of thin-wall machining of aluminum 7075-T6 alloy”. 5th International & 26th All India Manufacturing Technology, Design and Research Conference (AIMTDR), 2014, no. AIMTDR. pp. 135 (1–6).

D. Xu, P. Feng, W. Li, Y. Ma, and B. Liu, “Research on chip formation parameters of aluminum alloy 6061-T6 based on high-speed orthogonal cutting model”. Int. J. Adv. Manuf. Technol., 2014, vol. 72, no. 5–8, pp. 955–962, doi: 10.1007/s00170-014-5700-3.

C. Design, W. Zhao, P. Stief, J. Dantan, A. Etienne, and A. Siadat, “ScienceDirect ScienceDirect Effect of morphological evolution of serrated surface formation during high speed cutting Ti6Al4V A new methodology to analyze the functional and physical architecture of , Yutong product Liu oriented existing products for an a”. Procedia CIRP, 2018, vol. 77, no. Hpc, pp. 147–150, doi: 10.1016/j.procir.2018.08.262.

T. H. Pham, T. B. Mac, V. C. Tong, T. L. Banh, and D. T. Nguyen, “Simulation and experimental studies to verify the effect of cutting parameters on chip shrinkage coefficient and cutting forces in machining of A6061 aluminum alloy”. Adv. Mech. Eng., 2016, vol. 8, no. 10, pp. 1–11, doi:10.1177/1687814016673297.

P. Thi-Hoa, M. Thi-Bich, T. Van-Canh, B. Tien-Long, and N. Duc-Toan, “A study on the cutting force and chip shrinkage coefficient in high-speed milling of A6061 aluminum alloy”. Int. J. Adv. Manuf. Technol., 2018, vol. 98, no. 1–4, pp. 177–188, doi: 10.1007/s00170-017-1063-x.

T. H. Pham, D. T. Nguyen, T. L. Banh, and V. C. Tong, “Experimental study on the chip morphology, tool–chip contact length, workpiece vibration, and surface roughness during high-speed face milling of A6061 aluminum alloy”. Proc. Inst. Mech. Eng. Part B J. Eng. Manuf., 2020, vol. 234, no. 3, pp. 610–620, doi: 10.1177/0954405419863221.

J. Liu, Y. Bai, and C. Xu, “Evaluation of Ductile Fracture Models in Finite Element Simulation of Metal Cutting Processes”. J. Manuf. Sci. Eng., 2014, vol. 136, no. February, p. 011010, 2013, doi: 10.1115/1.4025625.

N. S. Brar, V. S. Joshi, and B. W. Harris, “Constitutive model constants for Al7075-T651 and Al7075-T6”. AIP Conference Proceedings, 2009, vol. 1195. pp. 945–948, doi: 10.1063/1.3295300.